RF and microwave photonic high bandwidth signal processing based on Kerr micro - comb sources

Integrated Kerr micro-combs are a powerful source for generating multiple wavelength channels to achieve photonic radio frequency (RF) and microwave signal processing, particularly in the context of transversal ﬁlters. They oﬀer competitive advantages including a compact device footprint, high versatility, large numbers of wavelengths, and wide Nyquist bands. Here, we review recent progress on Kerr micro-comb-based photonic RF and microwave high bandwidth temporal signal processing, including integral and fractional Hilbert transforms, diﬀerentiators as well as integrators. The strong potential of optical micro-combs for RF photonic applications in terms of functions and integrability is also discussed


I. INTRODUCTION
All-optical signal processing based on nonlinear optics has proven to be extremely powerful, particularly when implemented in photonic integrated circuits based on highly nonlinear materials such as silicon [1][2][3].All optical signal processing functions include all-optical logic [4], demultiplexing at ultra-high bit rates from 160Gb/s [5] to over 1Tb/s [6], optical performance monitoring (OPM) using slow light [7,8], all-optical regeneration [9,10], and others [11][12][13][14][15][16].Complementary metal oxide semiconductor (CMOS) compatible platforms are centrosymmetric and so the 2 rd order nonlinear response is zero.Hence, nonlinear devices in these platforms have been based on the 3 rd order nonlinear susceptibility including third harmonic generation [11,[17][18][19][20][21] and the Kerr nonlinearity (n2) [1,2].The efficiency of Kerr nonlinearity based all-optical devices depends on the waveguide nonlinear parameter (γ).Although silicon-oninsulator nanowire devices can achieve extremely high nonlinearities (γ), they suffer from high nonlinear optical losses due to two-photon absorption (TPA) and the resulting generated free carriers [2].Even if the free carriers are swept out by p-i-n junctions, silicon's relatively poor intrinsic nonlinear figure of merit (FOM = n2 / (β λ), where β is the TPA and λ the wavelength) of around 0.3 in the telecom band is too low to achieve good performance.While TPA can be turned to advantage for some all-optical functions [22][23][24], for the most part, silicon's low FOM in the telecom band is a limitation.This has motivated research on a range of alternate nonlinear platforms including chalcogenide glasses [25][26][27][28][29][30][31][32][33][34].However, while offering many advantages, these platforms are not compatible with CMOS processingthe basis of the silicon computer chip industry.
In 2007/8 new CMOS compatible platforms for nonlinear optics were reported that exhibited extremely low twophoton absorption in the telecommunications wavelength band.These included silicon nitride [35,36] as well as highindex doped silica glass (Hydex) [37][38][39][40][41][42][43][44][45][46][47], similar in its optical properties to silicon oxynitride.In addition to negligible nonlinear absorption, these platforms displayed a moderate Kerr nonlinearity, resulting in an extremely high nonlinear figure of merit as well as a nonlinear parameter that was high enough to support substantial parametric gain.Following the first report of micro-ring resonator (MRR) based frequency comb source driven by the Kerr optical nonlinearity in 2007 [48], the first fully integrated optical parametric oscillators were reported in 2010 [36,37] that were also CMOS compatible.Since then the field of integrated micro-combs, or "Kerr combs" has become one of the largest fields in RF and microwave photonic high bandwidth signal processing based on Kerr micro-comb sources Mengxi Tan, 1 Xingyuan Xu, 1* Jiayang Wu, 1 Roberto Morandotti, 2 Arnan Mitchell, 3  and David J. Moss 1  optics and photonics [47].Integrated optical Kerr frequency comb sources, or "micro-combs" are a fundamentally new and powerful tool to accomplish many new functions on an integrated chip, due to their ability to provide highly coherent combs of multiple wavelength channels, at the same time offering a very high degree of wavelength spacing control.Optical micro-combs are produced via optical parametric oscillation driven by modulational instability gain in monolithic MRRs.They offer significant advantages over more traditional multi-wavelength sources.Many innovative applications have been reported based on integrated Kerr micro-combs, from filter-driven mode-locked lasers [49][50][51][52] to quantum optical photonic chips [53][54][55][56][57][58][59][60][61], ultrahigh bandwidth optical fiber data transmission [62][63][64], optical neural networks [65][66][67], integrated optical frequency synthesizers [68].Micro-combs have been extensively reviewed [47, 69 -76].The success of the new CMOS platforms silicon nitride and Hydex motivated the search for even higher performing CMOS compatible platforms such as amorphous silicon [77] and silicon rich silicon nitride [78] that display a combination of low linear loss, high nonlinearity and very low nonlinear loss.
All-optical signal processing based on nonlinear optics has attracted significant interest over the years for its ability to achieve ultrahigh bandwidth without needing optical to electronic (or visa versa) conversion.It has been particularly important for a wide range of signal processing functions for both telecommunications and RF/microwave applications.RF photonic applications range from radar systems to signal generation and processing , and are attractive because of the ultra-high bandwidths that can be achieved as well as low transmission loss and strong electromagnetic interference immunity.There is a very wide range photonic RF approaches including techniques that map the optical filter response in the optical domain onto the RF domain.This is perhaps best represented by integrated devices based on stimulated Brillouin scattering [88][89][90][91][92][93][94][95], which has resulted in extremely high performance for RF resolutionbeing able to resolve features as fine as 32 MHz, at the same time achieving a stopband rejection > 55 dB.A key approach to achieving reconfigurable transfer functions for adaptive signal processing has been based on the transversal filter method [96][97][98][99][100] that operate by generating weighted, progressively delayed replicas of an RF signal imprinted on an optical carrier and then summing them via photo-detection.Transverse filters can realize a wide range of RF signal processing functions by only adjusting the tap weights, and so this method is very attractive to realize advanced RF filters that need to be dynamically adaptive.Both discrete laser diode arrays [101] as well as integrated and fibre Bragg grating arrays and sampled gratings [103] have been successful at supplying the required taps.However, while offering many advantages, these approaches suffer from significantly increased complexity as well as reduced performance due to limitations in the available number of taps.Alternative approaches, such as employing optical frequency comb sources achieved by electro-optic (EO) or acousto-optic (AO) modulation [102,104,105], can help overcome this problem, but they require multiple high frequency modulators that rely on high-frequency RF sources.Of these approaches, EO combs have been used the longest and have achieved significant success at realizing many powerful functions.
Integrated optical Kerr micro-combs are a relatively recent innovation and have been very successful -offering many advantages over other approaches that use multi-wavelength sources for RF applications.They have been demonstrated to be capable of achieving extremely high bit rate telecommunications systems as well as a very wide range of RF signal processing functions .They can generate frequency combs with a much larger spacing than electrooptic combs.EO combs and micro-combs are in fact complementary in many ways -EO combs focuses on finer wavelength spacings from 10's of MHz to 10 -20 GHz, while integrated micro-combs typically have much wider spacings from 10's to 100's of GHz and even into the THz regime.Larger comb spacings yield much wider Nyquist zones that are needed to achieve large RF bandwidths, whereas finer spacings provide much larger numbers of wavelengths or RF "taps", but at the cost of a much smaller Nyquist zone, or RF bandwidth.Micro-combs can provide higher numbers of wavelengths together with still being able to provide a large FSR, in a compact footprint.For RF transversal filters the number of taps, or wavelengths, dictates the available number of channels for, for example, RF true time delays as well as determining the performance of RF filters [85,121].Other systems such as beamforming devices [112] can also be greatly improved in terms of their quality factor and angular resolution.Other innovative approaches to filtering include techniques such as RF bandwidth scaling [125] that provide a certain bandwidth for each wavelength channel, and so the total operation bandwidth (maximum RF signal bandwidth that can be processed) will depend on the number of wavelengths, and will therefore be significantly enhanced by the use of micro-combs.
Recently [121], we reviewed transversal filtering and bandwidth scaling methods based on Kerr micro-combs applied to RF and microwave spectral filters.Here, we focus on RF and microwave high bandwidth temporal signal processing based on integrated Kerr micro-comb devices.We review both integral and fractional order Hilbert transformers and differentiators, as well as RF integrators.We discuss the trade-offs involved between using wide spaced micro-combs with an FSR of 200GHz [109][110][111] with recently reported record low FSR spaced micro-combs at 49 GHz, based on soliton crystals [122][123][124][125][126][127][128].We highlight their potential and future possibilities, contrasting the different methods and use of the differently spaced micro-combs.While 200GHz Kerr micro-combs have proven to be a powerful source for RF transversal filters, enabling high versatility as well as dynamic reconfigurability, the relatively large comb spacing FSR of ~1.6 nm restricts the number of taps to typically less than 21 wavelengths within the 30nm wide C-band.This is important since this transversal filters require optical amplifiers and spectral shapers that are typically only available in the telecommunications bands (1530-1620nm).This limitation in the tap number has restricted the performance of micro-comb based transversal RF filters in frequency selectivity, bandwidth, and dynamic versatility.To improve on this, we reported micro-comb-based photonic RF transversal filters operating with a record high number of taps − up to 80 wavelengths over the C-band [117].This is the highest number reported for micro-comb RF transversal filters, and has been enabled by a record low 49GHz FSR integrated Kerr micro-comb source.For filter applications [121] this enabled QRF factors for RF bandpass filters 4 times higher than that achievable with 200GHz combs.For temporal signal processing, this yields dramatic improvements in both bandwidth and reconfigurability.Our results confirm the feasibility of achieving high performance advanced as well as adaptive RF transversal filters for use in high bandwidth RF signal processing systems, at the same time providing reduced cost, footprint, and complexity.

II. INTEGRATED KERR MICRO-COMBS
The generation of micro-combs is a complex process that relies on a combination of high nonlinear optical parameters, low linear and nonlinear loss as well as engineered dispersion.Diverse platforms have been developed for micro-combs [47] such as silica, magnesium fluoride, silicon nitride, and doped silica glass [47,70,85].In 2008 [39] we reported efficient four-wave mixing at milliwatt power levels based on the 575GHz FSR devices that had a relatively low Q-factor of 60,000.This represented the first report of low power CW nonlinear optics in silica glass based MRRs.This was followed in 2010 by the first integrated micro-combs [37,38] in Hydex and silicon nitride -the first optical micro-combs that were realized in an integrated photonic chip, that were inspired by the micro-combs demonstrated in toroidal resonators [48].Another breakthrough came with the report of [116,117] integrated microcombs with record low spacings of < 50GHz which greatly expanded the number of wavelengths over the telecommunications band to 80 or more.Apart from a record low FSR, these micro-combs operated via a different process to single soliton states [66][67][68][69][70][71][72][73], called soliton crystals [129,130].Many other recent breakthroughs have been reported in micro-combs, such as ultralow pump power combs [131], dark solitons [132], laser-cavity solitons [133] and others [134][135][136][137][138][139].
The MRRs used in the work that is reviewed here were fabricated on a platform based on Hydex glass [37,38] using CMOS compatible fabrication processes.Ring resonators with Q factors ranging from 60,000 to > 1.5 million and with radii ranging from ~592 μm to ~135 μm and even smaller at ~48 μm, corresponding to FSRs of ~0.4 nm (~49 GHz), ~1.6 nm (~200 GHz), and ~4.5 nm (~575 GHz), respectively.The RF signal processing devices that are reviewed here were based on micro-combs with FSR spacings of 200GHz (Fig. 1a) and 49GHz (Fig. 1b).Hydex glass films (n = ~1.7 at 1550 nm) were deposited via plasma enhanced chemical vapour deposition, and then patterned by deep UV stepper based photolithography.The waveguides were etched by inductively coupled plasma reactive ion etching to achieve waveguides with very low surface roughness.Finally, an upper cladding layer composed of silica glass (n = ~1.44 at 1550 nm) was deposited.We typically a vertical coupling scheme between the bus and ring resonator, where the gap of about 200nm can be controlled by film growth, that is much more accurate than lithography.The advantages of the Hydex platform, particularly with respect to optical micro-combs, include its very low linear loss (~0.06 dB‧cm −1 ), its moderately high optical nonlinear parameter (~233 W −1 ‧km −1 ), and lastly, in particular its negligible nonlinear optical loss, even up to extremely high intensities of 25 GW‧cm −2 .We reported narrow resonance linewidths corresponding to Q factors of up to ~1.5 million (Fig. 1) for both the 49GHz and 200GHz FSR MRRs.After packaging the devices with fiber pigtails, the through-port insertion loss was typically 0.5 to 1 dB per faceta result of very efficient on-chip mode converters.
To generate micro-combs with the 200GHz FSR devices, the continuous-wave (CW) pump power was typically amplified to over ~ +30 dBm and then the wavelength was swept from blue to red near one of the TE resonances near ~1550 nm of the MRRs.When the detuning between the pump wavelength and MRR's cold resonant wavelength became small enough, thus allowing the intracavity power to reach a threshold, modulation instability gain induced oscillation occurred [47].Primary combs were generated with the spacing determined by the MI gain peakmainly a function of the intra-cavity power and dispersion.As the detuning was changed further, finally single-FSR spaced micro-combs eventually appeared.While the states that were reached by the micro-combs did not display soliton behaviour, we note that achieving rigorous single soliton states such as the dissipative Kerr solitons (DKS) [66] is not required.This is significant since, while much is now understood about DKS solitons and significant recent progress has been made [139], they still require complex pump dynamics involving simultaneous frequency and amplitude sweeping in both directions in order to "capture" or "kick" the soliton states out of the chaotic state.Our initial work on micro-comb applications was based on the 200GHz micro-combs operating in this partially coherent state that, while not exhibiting rigorous soliton behaviour, was nonetheless a relatively low noise state that managed to avoid the chaotic regime [47] and which we found was adequate for microwave applications.The spectra shown in Figs.1b and  1c are typical of the 200GHz combs in this initial microwave work, and clearly show that they are not a rigorous soliton states.They were successful at demonstrating a wide range of RF signal processing functions [85, 107, 109 -111].
Subsequently, we reported Kerr solitons with a record low FSR of 49GHz, based on a new class of soliton [129,130] called soliton crystals.Soliton crystals result from mode crossings, in our case in the C-band, and are easier and more robust to generate than DKS states, and indeed even easier than the partially coherent 200GHz FSR comb states.They can be generated even with manual tuning of the pump laser wavelength.The underlying physics behind this is that the internal cavity optical energy of the soliton crystal state is very close to that of the chaotic state.Therefore, when transitioning from chaos to the soliton crystal state, there is only a very small shift in internal energy and hence very little resonant wavelength jump.It is this "jump" in both internal energy and resonant wavelengths of the microresonator that makes DKS states more challenging to achieve.At the same time, this same issue makes the efficiency of the soliton crystal states (energy in the comb lines relative to the pump wavelength) much higher than DKS states (the single soliton states in particular).There is a trade-off with soliton crystal microcombs, though, in that their spectra are not flat but exhibit characteristic "curtain-like" patterns.While this can sometimes require spectral flattening, it has not posed a fundamental barrier to achieving a wide range of high performance RF and microwave processing functions.Soliton crystals also require mode-crossings in the resonator, and this can be somewhat challenging to design, over and above the requirement of anomalous dispersion that DKS states need.This, however, has not posed a barrier to fabricating many chips with a high yield [64].
When generating soliton crystals, we typically tuned the pump laser wavelength manually across a resonance (TE polarized).When the pump (with sufficient power) was aligned well enough with the resonance, a primary comb was generated, similar to the 200GHz states.In this case, however, as the detuning was changed further, distinctive 'fingerprint' optical spectra were observed (Fig. 2), arising from spectral interference between tightly packed solitons in the cavitysolitons that formed the soliton crystals [129,130].A small but noticeable and abrupt step in the measured intracavity power (Fig. 2(b)) was observed at the point where these spectra appeared.More dramatic was a a very significant reduction in the RF intensity noise (Fig. 2(c)) at this point.Together with the spectra shapes, these observations indicate soliton crystal formation [38], although to conclusively demonstrate this would need one to perform time-resolved autocorrelation pulse measurements.The key issue for the RF experiments was not the specific micro-comb state that was reached, but whether or not low RF noise and high coherence states were achieved, and we found that these were relatively straightforward to achieve through adiabatic pump wavelength sweeping.We found that overall soliton crystals provided by far the lowest noise states of all micro-combs, and have formed the basis for a microwave oscillator with low phase-noise [120].

III. RF TRANSVERSAL FILTER: THEORY AND EXPERIMENT
The transfer function of a general transversal structure can be described as [85] 1 0 () Where j = 1  , ω is the angular frequency of the input RF signal, M is the number of taps, T is the time delay between adjacent taps, and hk is the tap coefficient of the kth tap, which is the discrete impulse response of F(ω).The discrete impulse response can be calculated by performing the inverse Fourier transform of F(ω), and then temporally windowing it with a short cosine bell.The transversal structure is essentially equivalent to a finite impulse response digital filter, and both are fundamental tools for RF signal processing in general and photonic RF signal processing in particular.By properly designing the tap weights hk for each wavelength channel, the transfer function for different signal processing functions can be realized, including Hilbert transforms, differentiators and integrators.The Nyquist frequency of the response function, which determines the maximum RF frequency that the devices can operate at, is given by fNyquist = 1/2T.Figure 3 shows the schematic of a transversal filter based on a multi-wavelength source, showing that the principle consists of several functions: First, all of the wavelengths from the microcomb source are imprinted with the RF signal via an electro-optic modulatoressentially broadcasting, or multicasting, the RF signal onto all the comb lines.This is then followed by transmitting the wavelengths through a dispersive medium to acquire wavelengthdependent delays.Second-order dispersion, which yields a linear relationship between the wavelength and the delay, is generally employed to progressively separate the replicas.The delayed signals can be either separately converted into electronic RF signals or summed together upon photodetection.Separately converting the signals can be achieved with wavelength demultiplexers and photodetector arrays for applications such as RF true time delays [116].Summing the signals on all of the wavelengths forms the basis for RF transversal filters for signal processing functions [85].The large number of wavelengths supplied by the micro-combs has significant advantages for enhancing the transversal signal processor performance.The number and amplitude of progressively delayed RF replicas, or taps, determines the performance of the system.By setting the tap coefficients, a reconfigurable transversal filter with virtually any transfer function can be achieved, including both integral and fractional order Hilbert transformers [107,126], integral and fractional differentiators [109,127], bandpass filters [111,117,121], integrators [123], waveform generators [128] and much more.
Figure 4 shows the experimental setup for a transversal filter based on an integrated Kerr optical comb source with an FSR of 200GHz (Fig. 4(a)) as well as the setup based on a 49GHz (Fig. 4(b)) comb.In both cases the micro-combs, generated by the on-chip MRR, are amplified and fed to either one (200GHz comb) or two (49GHz comb) waveshapers for channel equalization and weighting.A 2 nd waveshaper was used for the 49GHz FSR comb to pre-flatten the nonuniform comb spectra of the soliton crystals.The power of each comb line is then set by the waveshaper according to the required tap weights.To increase the accuracy, real-time feedback control paths are used to read and shape the power of the comb lines.The comb lines are then spatially divided into two paths according to the sign of the tap coefficientsone path for negative weights and one for positive.Next, for the 200GHz micro-comb experiments the signal was passed through a 2×2 balanced Mach-Zehnder modulator (MZM) that was biased at quadrature.The 2×2 balanced MZM simultaneously modulated the input RF signal on both positive and negative slopes, thus yielding replicas of the input RF signal with phase and tap coefficients having both algebraic signs.For experiments with the 49GHz FSR microcomb, both positive and negative taps were achieved by spatially separating the wavelength channels according to the designed tap coefficients and then feeding them into the respective positive and negative input ports of a balanced photodetector (Finisar BPDV2150R) (Figure 4b).
For the system based on the 200GHz comb, the signal that was modulated by the MZM then went through ~2.122km of standard single mode fibre (SMF), where the dispersion was ~17.4 ps/(nm‧km), corresponding to a time delay T of ~59 ps between adjacent wavelengths, or taps (the channel spacing of the time delay lines equalled the FSR of the micro-combs), which resulted in a Nyquist frequency of ~8.45 GHz.The bandwidth of the systems was determined by the Nyquist frequency, which could be easily enlarged by decreasing the time delay which, because of the large FSR of the compact MRR, could reach over ~ 100 GHz.Finally, the weighted and delayed taps were combined upon photodetection with a high-speed photodetector (Finisar, 40 GHz bandwidth) which converted them back into RF signals.
For the transversal system based on the 49GHz FSR microcomb, the signal went through about 5km of standard SMF to provide the progressive delay taps.The dispersion of the fibre was the same (17 ps/nm/km) as the 200GHz system, which yielded a different time delay T of ~34.8 ps between adjacent taps.This yielded an operational bandwidth (Nyquist frequency, half of FSRRF) of about 14.36 GHz for the transversal filter.As before, this can be increased by decreasing the time delay (using a shorter spool of SMF), at the expense of having a reduced resolution in tuning.The maximum operational bandwidth of the transversal filter is limited by the comb spacing.For the 49 GHz comb, significant crosstalk between adjacent wavelength channels occurs for RF frequencies that are beyond 24.5 GHzhalf of the micro-comb's spacing.This issue can be addressed by employing a micro-comb source with a larger comb spacing, although this comes at the expense of providing fewer comb lines/taps across the C-band.Note that although standard optical fibre is often used to produce the dispersive delays, this can readily be done much more efficiently using other approaches.Typically, only about 2-km of SMF, yielding a dispersion of 34 ps/nm, is needed.This is within the range of multi-channel tunable dispersion compensators [140][141][142][143], which can also be designed with a builtin dispersion slope offset.This approach would not only yield a compact and latency free delay but would enable tunability to adjust the Nyquist zone.In the following sections, we will review progress made in high bandwidth temporal RF and microwave signal processing functions beginning with Hilbert transforms, followed by differentiation and then integration, all based on Kerr micro-combs.

IV. HILBERT TRANSFORMS
The Hilbert transform (HT) is a fundamental signal processing operation with wide applications in radar systems, measurement systems, speech processing, signal sampling, single sideband modulators, and others [144].Standard integral HTs perform a ± 90° phase shift around a central frequency, with an all-pass amplitude transmission.Fractional Hilbert transforms (FHTs) that yield a variable phase shift represent a powerful extension to the standard HT, with applications to secure single sideband communications [145], hardware keys [145,146], and in forming images that are edge enhanced relative to the input object, where one can select the edges that are enhanced as well as the degree of edge enhancement [147].Electronic fractional Hilbert transformers are limited in operation bandwidth [145,148], whereas photonic technologies offer broadband operation as well as strong immunity to EMI.Hilbert transformers based on free-space optics have been demonstrated [146,149] that achieve high performance but are bulky and complex.Phase-shifted fibre Bragg grating based Hilbert transformers typically have bandwidths of a few 100GHz [150][151][152][153] but only yield a precise FHT for signals with specific bandwidths, fixed fractional orders, and only operate on the complex optical field (not the actual RF signal).This also holds for integrated reconfigurable microwave processors [154] as well Bragg grating approaches [155].In practice, the FHT of the RF and microwave signals -not the complex optical fields − is what is most desired for RF measurement and signal reshaping [156][157][158][159][160][161][162][163].
Integrated Hilbert transformers realized using micro-ring or micro-disc resonators, Bragg gratings in silicon, and integrated InP-InGaAsP photonic chips yield compact devices with high stability and mass-producibility [154,155,[159][160][161].Nevertheless, they only operate on the complex optical field and generally only provide a limited phase shift tuning range.Transversal filter approaches offer high reconfigurability [162,163] but need many discrete lasers, thus increasing system size, cost, and complexity, and limiting the number of taps and therefore performance.Optical frequency combs (OFCs) provide a single high-quality source for many wavelengths, including mode-locked lasers [164], electro-optical modulators [165], and micro-resonators [166].Of these, Kerr micro-combs generated by microresonators provide many wavelengths with greatly reduced footprint.
The spectral transfer function of a general fractional Hilbert transformer can be expressed as [80,126]: where j = 1  , φ = P × π / 2 is the phase shift, and  denotes the fractional order.From Eq. ( 2), a FHT can be regarded as a phase shifter with ± φ phase shifts centered around a frequency ω, which becomes a classical integral HT when P = 1.The corresponding impulse response is a continuous hyperbolic function: For digital implementations, this hyperbolic function is truncated and sampled in time by discrete taps.The sample spacing Δt determines the null frequency fc = 1/Δt.The order of the FHT is continuously tunable by only adjusting the coefficient of the tap at t = 0 while keeping the same coefficients for the other taps [146].
To achieve a Hilbert Transform the normalized power of each comb line is given by: 1 / 2 0.5 where N is the number of comb lines, or filter taps, used in the filters, and n = 0, 1, 2, …, N-1 is the comb index.
In 2015, the first Kerr micro-comb based Hilbert transformers was demonstrated, with up to 20 taps [107] from a 200GHz comb that achieved a record RF bandwidth (5 octaves).Figures 5(a) and 5(b) show the shaped optical microcombs measured using an optical spectrum analyzer for the 12 and 20 tap filter cases, respectively.The designed tap weights, or wavelength target powers, are also shown as green crosses in Figs.5(a) and 5(b).The waveshaper was used to shape the powers of all comb lines successfully to within +/-0.5 dB of the target powers.This could easily be achieved since the waveshaper resolution of 10 GHz was much smaller than the comb spacing which was 200GHz at the time.Once the comb lines were attenuated in order to provide the correct tap coefficients of the impulse response associated with a HT, with the unused comb lines attenuated below the noise floor, the system RF frequency response both in amplitude and phase was then characterized with a vector network analyzer (VNA).
Figure 6a shows the measured photonic Hilbert transform filter RF amplitude frequency response for 12, 16 and 20 taps, respectively.All filters agree well with the theoretical calculations and show very low (< 3 dB) amplitude ripple.
All three filters have the same null frequency centred at 16.9 GHz, which corresponds to the tap spacing of t = 1/fc = 59 ps.This matches the difference in delay between the comb lines, equal to the micro-ring FSR of 1.6 nm, produced by propagation of the signal through the 2.122-km long spool of SMF that has the standard dispersion parameter of D = 17.4 ps/nm/km.The null frequency could be varied by using different fiber lengths to adjust the tap delay spacing or by using tunable dispersion devices.As expected, increasing the number of filter taps increases the filter bandwidth.With a 20-tap filter, the Hilbert transformer exhibited a 3-dB bandwidth extending from 0.3 GHz up to 16.4 GHz -a range of more than 5 octaves -which was a record for any approach to HTs at the time.It is possible to increase this bandwidth even further by using more comb lines in the filter and in fact only a small portion of the generated comb lines was actually used to realize the filter taps.The number of filter taps that could be achieved was in fact limited by the bandwidth of the waveshaper, which was restricted to the C-band, as well as the gain bandwidth of the erbiumdoped fiber amplifiers (EDFAs).The amplitude ripple within the passband can be reduced even further by apodizing the tap coefficients compared to the ideal hyperbolic function.Figure 6(b) shows the measured phase response of filters with different numbers of taps, showing a very similar response.Each shows a relatively constant phase of near -90 o within the passband.There are some deviations from the ideal -90 o phase at frequencies close to zero and particularly for the null frequency fc = 16.9GHz.
Recently, [126] Tan et.al used a Kerr microcomb having a significantly finer comb spacing of 49GHz that provided a much larger number of comb lines (80 in the C band) to demonstrate a fractional Hilbert transformer (FHT).By programming and shaping the comb lines according to calculated tap weights, FHTs with phase shifts of 15°, 30°, 45°, 60°, 75°, and 90° corresponding to fractional orders of 0.17, 0.33, 0.5, 0.67, 0.83, and 1, respectively, were achieved.A maximum of 17 wavelengths were used, with the space between the 8th and 9th taps and 9th and 10th taps being 0.8 nm, while the remaining spacings were 1.6 nm.This was done in order to maximize the Nyquist zone.The delay line was provided by a 2.1-km length of single mode fibre (β = ~17.4ps / nm / km) that generated a time delay between channels of τ = L × β × ∆λ = ~29.4ps, corresponding to a FSRRF of 1/2τ = ~17 GHz.This bandwidth can be increased by using a shorter length of fibre.
The theoretical amplitude and phase response of the FHTs with 15°, 30°, 45°, 60°, 75°, and 90° phase shifts are shown in Figs.7 (a)-(f) solid black curves for different numbers of taps.Figures 8(a) and (b) show the RF amplitude and phase frequency response for a FHT with a 45° phase shift with 5, 9, 13 and 17 taps, respectively.Figure 8c) shows the 3dB bandwidth as a function of the number of taps.As expected, the bandwidth increases with the number of taps.With 17 taps, the operating 3-dB bandwidth for base-band RF signals was 480 MHz to 16.45 GHz -more than 5 octaves and ±0.07 rad phase variation within the 3-dB bandwidth.These numbers represent record performance for FHTs.For a standard 90° HT the soliton crystal micro-comb provided more than 40 taps, thereby reducing the root-meansquared error (RMSE) and amplitude ripple within the passband [126].As seen in Fig. 8 (c), the theoretical 3-dB bandwidth increases rapidly with the number of taps up to 17 taps, after which it levels off, so that 17 to 20 taps is close to the optimum number.
Figure 9 (ii)-(iii) presents the simulated (red dashed curves) and measured (blue solid lines) response of the fractional Hilbert transformers with variable orders ranging from 0.166 − 0.833 (phase shifts 15° − 90°).The normalized frequency response for both the magnitude and phase of the FHTs are shown together with the temporal response (Fig. (iv)).The amplitude variations are less than +/-1.5dB between 480MHz and 16.45GHz and the phase variations are about ±0.07 rad within the 3-dB passband.System demonstrations of a real-time FHTs applied to Gaussian input pulse signals were also performed.Fig. 9 (iv) shows a pulsed waveform after processing by the fractional Hilbert transformer along with the simulated results (Fig. 9 (iv), red dashed curves).The detailed performance parameters are listed in Table I of Ref. [126].As can be seen, the measured curves closely match the theoretical counterparts, achieving good performance that agrees well with theory.
In comparing the earlier results achieved with the 200GHz FSR microcomb with the more recent FHT results achieved with the soliton crystals having a 49-GHz FSR spacing, it is clear that the soliton crystal based results yield superior performance over the 200-GHz comb-based transformer in terms of bandwidth, mainly because of the larger number of available taps.Nonetheless, we note that it is not always the case that a smaller FSR comb is necessarily better.The 200-GHz devices are capable of reaching extremely high RF bandwidths, particularly in tunability, approaching 100GHz, since this represents the Nyquist zone of these combs, whereas the 49GHz devices are limited to about 25GHz.In summary, our good agreement with theory confirms that the approach of using microcombs is a very effective way to implement high-speed reconfigurable HTs and FHTs with lower complexity, reduced footprint, and lower cost.
For the most part, photonic differentiatorsboth integral and fractional -have focused on generating the derivative of the complex optical field, rather than the actual RF signal.For example, a photonic differentiator based on a dualdrive MZM together with an RF delay line, [174] although successful, was limited in processing speed by the bandwidth of the RF delay line.Photonic differentiators based on optical filters [175] feature high speeds of up to 40-Gb/s, although they only work for a fixed (and typically integral) differentiation order and generally lack flexibility or reconfigurability.To implement highly reconfigurable differentiators, transversal schemes have been investigated using discrete laser arrays [169,180,181].While this is a powerful and attractive approach, it also presents some limitations, chiefly in the number of wavelengths that can be supplied.Increasing the number of lasers to provide more taps dramatically increases the system size, cost, and complexity, thus limiting the processing performance.Using a single source that can simultaneously generate a large number of high-quality wavelength channels would be highly advantageous.Recently [109], a photonic RF integral differentiator with 8 taps, achieved using a 200-GHz FSR microcomb source was demonstrated, that generated the 1 st , 2 nd , and 3 rd order derivatives operating at RF bandwidths up to 17 GHz with a potential bandwidth of 100 GHz.
An Nth-order temporal fractional differentiator can be considered as a linear time-invariant system with a transfer function given by [168] ( ) ( ) where j = 1  , ω is the RF angular frequency, and N is the differentiation order which can be fractional and even complex [184,185].According to Equation 5, the amplitude response of a temporal differentiator is proportional to |ω| N , whereas the phase response has a linear profile, with a phase jump of Nπ at null frequencies.
Using the transverse filter approach to RF photonic differentiators yields a finite set of delayed and weighted replicas of the input RF signal in the optical domain, which is then combined upon detection.The transfer function from Eq. ( 5) becomes where M is the number of taps, an is the tap coefficient of the n-th tap, and T is the time delay between adjacent taps.It should be noted that differentiators that achieve the function based on Eq. ( 6) are intensity RF differentiators, i.e., the output RF signal after being combined upon detection yields an exact differentiation of the input RF signal, in contrast to optical field differentiators that produce the derivative of complex optical fields [167,171,153,154,[185][186][187].
Recently, [109] the first use of a micro-comb to achieve RF differentiation was reported, demonstrating integral 1 st , 2 nd , and 3 rd order intensity differentiators.That demonstration was achieved with a 200GHz FSR Kerr micro-comb using 8, 6, and 6 taps, respectively.It achieved a dynamic range, determined by the EDFA, of ~30 dB.More taps are needed when the differentiation order increases, and for a fixed number of taps, increasing the order of differentiation also increases the required power dynamic range.In order to obtain better performance for a given number of taps, the operation bandwidth of the integral differentiators was decreased to half of the Nyquist frequency.To implement the temporal differentiator in Eq. ( 5), tap coefficients in Eq. ( 6) were calculated based on the Remez algorithm [188].The calculated tap coefficients for 1 st , 2 nd , and 3 rd order differentiation are listed in Table I of [109].As for demonstrations of other RF functions, since the 200GHz Kerr comb was not flat, real-time feedback control was used to increase the accuracy of the comb shaping.Both the phase and amplitude responses of the 1 st , 2 nd , and 3 rd order differentiators are shown in Figs. 10 (a)-(c) for different numbers of taps.As the number of taps increases, the discrepancies between the ideal and realized amplitude responses of the transversal filter based differentiators are improved for all three orders.In contrast the phase response of the transversal filters is identical to that of the ideal differentiators regardless of the number of taps.
The shaped optical comb spectra shown in Figs.11 (b)-(d) reveal a good match between the measured comb lines' power (red solid line) and the calculated ideal tap weights (green crosses).Figures 12 (a-i), (b-i), and (c-i) show the measured and calculated amplitude response of the differentiators.The corresponding phase response is depicted in Figs. 12 (a-ii), (b-ii), and (c-ii) where it is clear that all three differentiators agree well with theory.The FSR of the RF response spectra was ~16.9 GHz, consistent with expectations given the time delay between adjacent taps.By adjusting the FSR of the transversal filter through varying the dispersive fibre delay or programming the tap coefficients, a variable operational bandwidth for the intensity differentiator can be achieved, which is advantageous for the changing requirements of different applications.In particular, the ability to change the order of the differentiator simply by changing the tap weights offers a powerful way of dynamically changing the functionality of the system in real time without needing to modify any hardware.This is a feature that is not common to other approaches to differentiation, particularly optical filter-based systems.
Systems demonstrations of real-time signal differentiation were also performed for Gaussian input pulses having a full-width at half maximum (FWHM) of ~120 ps, as shown in Fig. 13 (a).The generated waveforms of the output signals, representing the different order derivatives, are shown in Figs. 13 (b)-(d) (blue solid curves), together with the theoretical results (red dashed curves).The experimental Gaussian pulse shown in Fig. 13 (a) was used as the input RF signal for the theoretical calculations.The measured curves closely match theory.Unlike the optical field differentiators [167,171,153,154,[185][186][187], the temporal derivatives of the RF intensity profiles can be observed, indicating that intensity differentiation was successfully achieved.For the 1 st , 2 nd , and 3 rd order differentiators, the calculated RMSE between the measured and theoretical curves are ~4.15%,~6.38%, and ~7.24%, respectively.
Recently, [127] Tan et.al reported the first fractional-order photonic RF differentiator that operates directly on the RF signal rather than the complex optical field.It was based on a record-low 49-GHz-FSR Kerr micro-comb source, which provided a large number of comb lines (80 in the C band), resulting in a broad operation bandwidth of 15.49 GHz.By programming and shaping the comb lines according to the calculated tap weights, reconfigurable arbitrary fractional orders ranging from 0.15 to 0.9 were demonstrated.System demonstrations of real-time fractional differentiation of Gaussian input pulses were also performed.The good agreement between theory and experiment confirmed that this approach as an effective way to implement high-speed reconfigurable fractional differentiators with reduced footprint, lower complexity, and potentially lower cost.
The success of the differentiator resulted from both the use of soliton crystals combined with the low FSR of 48.9 GHz, that generated over 80 wavelengths, or taps, in the C-band.The performance of the system was greatly aided by the soliton crystal's extremely robust and stable operation, ease of initiation and generation and as well as its much higher intrinsic efficiency, all of which are enabled by the integrated CMOS-compatible platform.The relationship between the number of taps and the performance of the fractional differentiator was also investigated.Figure 14 shows the theoretical transfer function of the fractional order differentiator for six different orders and for varying numbers of taps, compared to the ideal theoretical results.As can be seen, the operational RF bandwidth of the differentiatorwithin which the slope coefficients of the simulated and ideal amplitude responses match closely-increases with the number of taps. Figure 15 (a) shows that the number of taps is critical to the operational bandwidth for fractional differentiators, which is evident in the experimental results for the fractional order of 0.45 (Figs. 15 (b) and (c)).When the number of taps was increased to 27, the bandwidth of the fractional differentiator reached 15.49 GHz, equivalent to over 91% of the Nyquist band.In the experiments, up to 29 comb lines were employed to generate the taps.To increase the number of taps, the optical signal-to-noise ratio, which was subject to the optical amplifiers' noise, would need to be increased.
The shaped comb spectra used to generate the derivatives are shown in Fig. 16, where it is evident that the optical power for each comb line matched the designed tap coefficients well..The transmission frequency response of the fractional differentiator was characterized with a VNA.The power response of the differentiator showed a bandwidth ranging from DC to 15.49 GHz.As shown in Fig. 17, the range of fractional orders that the system was able to achieve was a result of the close agreement between theory and experimental in terms of the slope coefficients of the power response and phase shift in the phase response.Figure 18 shows the time domain performance of the fractional differentiator for all orders, using a baseband RF Gaussian pulse with a FWHM of ~200ps (Fig. 18) as the input signal, generated by an arbitrary waveform generator.The good agreement with theory reflects the range of orders that are achievable with our approach to realizing a reconfigurable fractional differentiator.

VI. INTEGRATION
Temporal integration is another key fundamental function in signal processing systems.Photonic techniques offer a broad bandwidth, in contrast to electrical integrators that are subject to the electronic bandwidth bottleneck, along with a strong immunity to EMI, as well as low loss [79,80,189].Significant work has been reported on photonic integrators, including gratings based approaches [190][191][192] and methods using micro-ring resonators (MRRs) [15,42,193].These approaches have achieved optical integration with a time resolution as short as 8 ps [193] as well as offering a large time-bandwidth product due to the availability of very high-Q resonant structures.However, these approaches still face limitations for RF signal processing, including the fact that they are not adjustable in their performance parameters such as temporal resolution or length of integration window.Hence, they lack the flexibility to process RF signals with different bandwidths and integration time windows.Probably more importantly, those approaches rely on processing the optical signals -they cannot directly process RF signals without electrical to optical interfaces.Another important approach to photonic integrators is based on transversal structures, that offers a high degree of reconfigurability and accuracy owing to the parallel scheme where each path can be controlled independently [194][195][196].By tailoring the progressive delay, RF signal integration with a reconfigurable operational bandwidth can be achieved [194][195][196].Still, however, these still face limitations arising from the limited number of channels in cases where diode laser arrays or electro-optical comb sources were employed.These approaches have a significant trade-off between the number of wavelengths and system complexity and ultimately they result in a limited number of channels which, and in turn, limits the time-bandwidth product.
Integrated Kerr micro-combs [38,47,[68][69][70]118,197] offer many advantages for RF integration, including a very high higher number of wavelengths as well as a greatly reduced footprint and complexity.Recently, a highly reconfigurable photonic RF temporal integrator was demonstrated with an integrated soliton crystal micro-comb source [123], where the RF signal was imprinted onto the micro-comb lines and progressively delayed via dispersion, and then summed upon detection.The large number of taps, or wavelengths (81) used in those experiments resulted in a large integration time window of ~6.8 ns with a time resolution as short as ~84 ps.The integrator was successfully tested with different input signals, with experimental results matching well with theory.
Figure 19 shows the operation principle of the transversal filter based photonic RF integrator.The integration process can be achieved via a discrete time-spectrum convolution operation between an RF input signal f (t) and a flattened micro-comb.With a delay step Δt, the operation is: ) where j = 1  , N is the total number of wavelengths.After the replicas of f(t) are progressively delayed and then summed, the temporal integration of the function f (t) results, with a time resolution given by [194] Δt, an operation bandwidth of 1/Δt, and a total integration time window of T = N × Δt.The frequency-domain transmission response of an ideal continuous, or non-discrete, integrator is linear to 1/(jω), where ω is the angular frequency.The frequency transmission response of the discrete integrator is a low pass sinc filter [111,117], given by (8) The experimental setup of the photonic RF integrator was similar to that shown in Figure 4, and was based on a soliton crystal micro-comb with an FSR of ~49 GHz.The soliton crystal micro-comb featured very low intensity noise to the extent that it has even been used as a photonic local oscillator [120].Thus, the noise of the micro-comb source did not introduce any observable deterioration in the overall noise performance of the integrator.After flattening the micro-comb spectral lines with a WaveShaper, the RF signal was imprinted onto the comb lines via an electro-optical modulator (EOM).The replicas were progressively delayed by a ~13km spool of standard optical fibre SMF and summed upon photodetection with a high-speed photodetector.The delay between the adjacent wavelengths (Δt) was set by the dispersion, length of fibre and spacing between the comb lines, and this in turn determined the resolution of the integrator [194].The temporal resolution was ~ 84 ps and in theory can be made arbitrarily small by reducing the amount of dispersion in the delay line, although with a trade-off that the integration window also decreases.Sixty comb lines in the C-band were selected, yielding an integration time window (T = N × Δt) of 60 × 84 ps = 5.04 ns (yellow shaded region in Fig. 20).The operation bandwidth of the integrator was 1/Δt =11.9 GHz.Signal integration for different RF input signals was performed.The red curves in Figs.20(a)−(c) show the results for Gaussian pulses (blue curves) with a FWHM from 0.20 ns to 0.94 ns, with the integration window T (~5 ns) matching with theory well (5.04 ns).Figures 20(d)−(e) show the results for dual Gaussian pulses with time intervals of 1.52 ns and 3.06 ns, where it is clear that the experimental results (red curves) illustrate the performance of the integrator by exhibiting three distinct intensity steps in the integration waveforms.The left step corresponds to the integration of the first pulse while the middle step reflects the integration of both of the two initial pulses, and finally the right step shows the integration of only the second pulse since it is beyond the integration window of the first pulse.The integrator was further tested with a rectangular input waveform having an equal width to the integration window (5 ns).The measured integrated waveform exhibited a triangular shape that matched well with theory (gray curve).
Figure 20 shows small residual discrepancies between experiment (red curves) and theory (grey curves).The errors were a result of the non-ideal impulse response of the system, caused by a number of relatively small effects that include gain variation with wavelength of the optical amplifier, modulator and photodetector.To verify this, the impulse response of the system was measured with a Gaussian pulse input.Since the time resolution of the system (~ 84 ps) was much less than the pulse width, the wavelength channels were separated into multiple subsets (each with a much larger spacing between the adjacent comb lines and thus obtained a temporal resolution larger than the input pulse duration), and their impulse responses measured sequentially.Figure 21(a) shows the measured impulse response of the system, which was not flat even when the comb lines were perfectly flattened.The measured impulse response and the input RF signal in Fig. 20 was used to calculate the corresponding integral output, with the results matching the experiment well, showing that the errors were induced by the non-ideal impulse response of the system.
These errors are in fact straightforward to compensate for.To reduce the errors, a more accurate comb shaping was used where the error signal of the feedback loop was generated directly by the measured impulse response, instead of the optical power of the comb lines.Thus this implicitly had the wavelength dependence of the components built-in.A flattened impulse response was obtained (Fig. 21(b)), which was much closer to the ideal impulse response than Fig. 21(a).The integration was then performed with the same RF inputs, the results of which are shown in Fig. 22.Note that during this measurement, 81 wavelength channels were enabled by the impulse response shaping process, so that the integration time window (T = N × Δt) increased to 81 × 84 ps = 6.804 ns, resulting in an operation bandwidth of 1/84ps = 11.9GHz and a time-bandwidth product of 6.804 ns × 11.9 GHz = ~81 (approximately equal to the number of channels N).The measured integrals (red curves, Fig. 22) show significantly better agreement with theory, indicating the success of the compensating impulse response shaping method as well as the overall power and feasibility of this approach to photonic RF integration.

VII. DISCUSSION
We have reviewed recent progress on the use of Kerr micro-combs for high bandwidth temporal RF and microwave signal processing, focusing on integral and fractional order Hilbert transformers, high order and fractional differentiators, both with continuously tunability in their order, and finally RF integrators.Micro-combs produce a large number of comb lines that greatly increase the performance and processing bandwidth of RF systems in terms of both the amplitude and phase response.They have shown their powerful capabilities for RF signal processing due to their large number of comb lines, their compact footprint, and large comb spacings that can be generated compared to all other approaches such as those using electro-optic combs.The devices reached operation bandwidths of ~ 16 GHz, for the 49 GHz devices and ~ 25 GHz for 200GHz FSR combs, evaluated both in the frequency domain using Vector Network Analyzers and in the time domain with Gaussian pulse input signals.
For transversal frequency-domain signal processors such as Hilbert transformers and differentiators, the number of wavelengths determines the number of taps, which in turn directly determines the system performance.We have highlighted the advantages of using Kerr micro-combs as the basis for RF photonic microwave transversal filters, illustrating the tradeoffs between using widely spaced micro-combs (200 GHz) and record-low spaced micro-combs (49 GHz) in terms of performance.The greater number of lines supplied by the 49GHz comb (80 versus 20 for the 200-GHz device) yielded significantly better system performance.On the other hand, the 49-GHz device is more limited in operational bandwidth, being restricted to roughly the Nyquist zone of 25 GHz, whereas the 200-GHz devices were able to reach RF frequencies well beyond what conventional electronic microwave technology can achieve.
Two types of combs employed to realize RF functions were qualitatively very different.Apart from the spacings being very different, the widely spaced 200GHz FSR microcomb operated in a quasi-coherent state that did not feature solitons, whereas the low spaced microcomb with an FSR of 49GHz operated in a state referred to as soliton crystals.Within the optical C band, the 49GHz spaced microcomb enabled up to 90 comb lines, yielding significantly better performance for the temporal signal processors than the than the 200GHz spaced microcomb which only allowed 20 taps in the C-band.Further, the soliton crystal states offered many other advantages such as much lower noise, higher stability, and much easier generation including the ability to even initiate soliton crystals through simple manual tuning of the pump wavelength.However, on the other hand the 49GHz combs generally yielded much smaller Nyquist bandwidths typically near ~16 GHz.For the transversal temporal signal processors such as the integrators, the large number of wavelengths brought about a large number of broadcasted RF replicas, thus yielding a large integration window for the integrator.The temporal response of the integrator was measured with a diverse range of RF inputs, verifying a integration window of 6.8 ns and a time feature as fast as 84 ps.The good agreement with theory and experiment verified that this approach is an effective way to implement high-speed reconfigurable signal processing featuring high processing bandwidths, for future ultra-high-speed microwave systems.
We believe that micro-combs will bring further benefits to RF photonic signal processing in many respects.First, the coherent nature of the soliton states will enable more advanced RF functions such as wideband frequency conversion and clock generation.Maturing nanofabrication techniques have allowed the realization of high-Q MRRs for comb generation with FSRs ranging from 10s' of GHz [119] up to the THz regime [47], covering the full RF bands of interest for almost any integrated RF system.The wide available FSR spacing of optical micro-combs allows for a large Nyquist zone up to 100's of GHz.This is well beyond the processing bandwidth of electronic devices and is also challenging for mode-locked lasers and OFCs obtained by EO modulation.With tailored dispersion, ultra-wideband bandwidth micro-combs -even up to octave-spanning and beyond, [71] can be achieved, thus enabling a very large number of wavelength channels with a single on-chip source, to work in conjunction with broadband opto-electronic equipment.This approach enables significantly enhanced wavelength-division parallelism for massive data transmission and processing [62][63][64] for many applications including radio-over-fibre systems, for example.
Perhaps most importantly, the high reconfigurability of micro-comb based programmable RF photonic transversal filters enables one to achieve highly versatile processing functions with dynamic real-time reconfigurability so that the same system can be dynamically reprogrammed to perform a wide range of different functions without having to alter any hardware.By simply programming and shaping the comb lines according to different specific tap coefficients, the same physical equipment can be employed to achieve multiple signal processing functions.Such a high degree of reconfigurability is unprecedented for photonic RF signal processors and enables highly reconfigurable processing functions and high processing accuracy that typically cannot be obtained by passive photonic integrated circuits or via optical analogue signal processing.Further, very wide operational RF bandwidths can be achieved for diverse computing requirements of many practical applications.Photonic transversal filters are essentially equivalent to filters achieved via purely digital signal processing, but implemented by photonic hardware.
There are a number of factors that can lead to tap errors during the comb shaping, thus leading to non-ideal impulse responses of the system as well as deviations between the experimental results and theory.These factors mainly include the instability of the optical micro-combs, the accuracy of the waveshapers, the gain variation with wavelength of the optical amplifier, the chirp induced by the optical modulator, and the third-order dispersion of the dispersive fibre.To combat this, real-time feedback control paths can be employed to effectively reduce the errors.In this approach, the power of the comb lines is first detected by an optical spectrum analyser (OSA) and then compared with the ideal tap weights, generating an error signal that is fed back into the waveshaper to calibrate the system and achieve accurate comb shaping.To further reduce the tap errors and improve the accuracy of comb shaping, the error signal of the feedback loop can be generated directly by the measured impulse response, instead of the raw optical power of the comb lines.In this approach, replicas of an RF Gaussian pulse are measured at all wavelengths to obtain the impulse response of the system, whose peak intensities are further extracted to obtain accurate RF-to-RF wavelength channel weights.Following this, the extracted channel weights are subtracted from the desired weights to obtain an error signal that is used to program the loss of the Waveshaper.After several iterations of the comb shaping loop, an accurate impulse response that compensates the non-ideal impulse response of the system can be obtained, thus significantly improving accuracy of the RF photonic transversal filter based signal processors.This only requires a one-time calibration process.
Finally, although the results reviewed here relied on some benchtop components, such as the commercially available Waveshaper, RF photonic signal processors based on Kerr micro-combs have significant potential to achieve much higher levels of integration with current nanofabrication techniques.To begin with, the most important component is the micro-comb source itself, which not only is already integrated but is fabricated with CMOS compatible processes.Globally established CMOS fabrication foundries can achieve advanced hybrid integration of microcomb sources and Ⅲ-Ⅴ devices, and this will potentially enable monolithic integration of the entire RF system.Other key components have been realized in integrated form with state-of-art nanofabrication techniques [198][199][200], including the optical pump source [131,139], LiNO3 modulators [200], optical spectral shapers [198], large dispersion media [199] and photodetectors.Further, advanced integrated microcombs have been demonstrated [139] that can generate soliton crystals reliably in turn-key operation.Monolithically integrating the whole RF processing system would greatly strengthen the performance, compactness and energy efficiency of the system.Even without this, however, using the discrete integrated comb sources to replace discrete laser arrays already yields significant benefits for RF and microwave systems in terms of performance, size, cost, and complexity.

VIII. CONCLUSION
We review recent work on the applications of Kerr micro-combs to photonic RF and microwave temporal signal processing based on transversal filters.Optical micro-combs bring a new generation of compact multi-wavelength sources to the RF photonics community and offer enormous possibilities for achieving high-performance RF signal processing with higher performance, reduced footprint, lower complexity, and potentially lower cost.By programming and shaping the comb lines according to calculated tap weights, diverse signal processing functions can be designed and have been experimentally demonstrated.We focus on fractional and integral order Hilbert transforms and differentiators as well as an RF integrator, based on integrated Kerr micro-comb sources that operate on the RF signal rather than the complex optical field.Real-time system demonstrations are also performed and show good agreement with theory.These results verify that the Kerr micro-comb is a highly effective tool to implement high-speed reconfigurable signal processing for future ultra-high performance RF systems                              (d-e) dual Gaussian pulses with time intervals of 1.52 and 30.6 ns, and (f) a triangular waveform with a width of 5.00 ns.The blue curves denote the input signal, the red curves denote the measured integration results, the gray curves denote the ideal integration results, and the green curves denote the integration results calculated with the measured impulse response of the system.

Fig. 1 .
Fig. 1.Schematic illustration of the integrated MRRs for generating the Kerr micro-comb for both (a-c) 200GHz FSR combs and (d-j) 49GHz combs.(b, c) Optical spectra of the micro-combs generated by 200GHz MRR with a span of (b) 100 nm and (c) 300 nm.(j) Optical spectra of the micro-combs generated by 50GHz MRR with a span of 100 nm.(e) Drop-port transmission spectrum of the integrated MRR with a span of 5 nm, showing an optical free spectral range of 49 GHz.(f) A resonance at 193.294 THz with full width at half maximum (FWHM) of 124.94 MHz, corresponding to a quality factor of 1.549×10 6 .

Fig. 2 .
Fig. 2. (a, d, e) Optical spectra of various soliton crystal micro-combs.(b) Optical power output versus pump tuning, showing the very small power jump at the onset of soliton crystal combs.(c) Transition from high RF noise chaotic state to low noise state of the soliton crystal comb.

Fig. 5 .
Fig. 5. Shaped optical spectra showing the weight of each tap for: (a) 12 tap filter, and (b) 20 tap filter

Fig. 6 .
Fig. 6.Measured system RF frequency response for different number of filter taps: (a) amplitude; and (b) phase response.

Fig. 8 .
Fig. 8. (a) and (b) Simulated and measured amplitude and phase response for the FHT for different numbers of taps for a FHT phase shift of 45°.(c) Simulated and experimental results of 3-dB bandwidth with different taps for a phase shift of 45°.Separate figure c into its own figure

Fig. 10 .
Fig. 10.Simulated RF amplitude and phase responses of the (a) first-, (b) second-, and (c) third-order temporal differentiators.(d) RMSEs between calculated and ideal RF amplitude responses of the first-, second-, and third-order intensity differentiators as a function of the number of taps.

Fig. 11 .
Fig. 11.(a) Optical spectrum of the generated Kerr comb in a 300-nm wavelength range.Inset shows a zoom-in spectrum with a span of ~32 nm.(b)-(d) Measured optical spectra (red solid) of the shaped optical combs and ideal tap weights (green crossing) for the first-, second-, and third-order intensity differentiators.

Fig. 14 .
Fig. 14.Simulated transfer function of different fractional differentiation orders with varying number of taps.

Fig. 15 .
Fig. 15.(a) Relationship between the number of taps and operation bandwidth.(b, c) Experimentally demonstrated fractional differentiator with varying number of taps.

Fig. 16 .
Fig. 16.Optical spectra of the shaped micro-comb for different fractional orders.

Fig. 17 .
Fig. 17.Simulated and measured the transmission response of the fractional differentiator at different orders ranging from 0.15 to 0.90.

Fig. 18 .
Fig. 18.Simulated and measured RF Gaussian pulse output temporal intensity waveform after the fractional differentiator.

Fig. 20 .
Fig. 20.Experimental results of the micro-comb-based RF integrator after comb optical power shaping for input (a-c) Gaussian pulses with FWHM of 0.20, 0.38 and 0.94 ns,(d-e) dual Gaussian pulses with time intervals of 1.52 and 30.6 ns, and (f) a triangular waveform with a width of 5.00 ns.The blue curves denote the input signal, the red curves denote the measured integration results, the gray curves denote the ideal integration results, and the green curves denote the integration results calculated with the measured impulse response of the system.

Fig. 21 .
Fig. 21.Measured impulse response of the integrator (a) after comb optical power shaping and (b) after impulse response shaping using a Gaussian RF input pulse.

Fig. 22 .
Fig. 22. Experimental results of the micro-comb-based RF integrator after impulse response shaping for input (a-c) Gaussian pulses with FWHM of 0.20, 0.38 and 0.94 ns, (d-e) dual Gaussian pulses with time intervals of 1.52 and 3.06 ns, and (f) a triangular waveform with a width of 5.00 ns.The blue curves denote the input signal, the red curves denote the measured integration results.